LH1533AACTR www.vishay.com vishay semiconductors rev. 1.8, 03-aug-11 1 document number: 83831 for technical questions, contact: optocoupleranswers@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 dual 1 form a solid-state relay description the lh1533 (dual 1 form a) relays are spst normally open switches that can replace electromechanical relays in many applications. they are cons tructed using a gaaias led for actuation control and an integrated monolithic die for the switch output. the die, fabricated in a high-voltage dielectrically isolated technology is comprised of a photodiode array, switch co ntrol circuitry, and mosfet switches. in addition, the re lays employ cu rrent-limiting circuitry, enabling them to pass lightning surge testing as per ansi/tia-968-b and other regulatory surge requirements when overvolt age protection is provided. featurtes ? dual channel (lh1550) ? current limit protection ? isolation test voltage 5300 v rms ? typical r on 28 ? ? load voltage 350 v ? load current 90 ma ? high surge capability ? clean bounce free switching ? low power consumption ? smd lead availabl e on tape and reel ? compliant to rohs directive 2002/95/ec and in accordance to weee 2002/96/ec applications ? general telecom switching - on/off hook control - ring delay - dial pulse - ground start - ground fault protection ? instrumentation ? industrial controls i179034_9 13 24 86 75 s 2' s 2 s 1 s 1' s 2' s 2 s 1 s 1' v de i179034_11 smd agency approvals ul1577: file no. e52744 system code h, double protection csa: certification no. 093751 bsi/babt: certification no. 7980 din en: 60747-5-2 (vde 088 4)/60747-5-5 (pending), available with option 1 fimko: approval ordering information lh1533a##tr part number electr. variation package config. tape and reel package ul, csa, bsi, fimko smd-8, tape and reel LH1533AACTR > 0.1 mm s md-8
LH1533AACTR www.vishay.com vishay semiconductors rev. 1.8, 03-aug-11 2 document number: 83831 for technical questions, contact: optocoupleranswers@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? stresses in excess of the abso lute maximum ratings can cause permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of the time can adversely affect reliability. (1) refer to reflow profile for soldering conditions for surface mount ed devices (smd). refer to wave profile for soldering conditi ons for through hole devices (dip). note ? minimum and maximum values are testing requirements. typical valu es are characteristics of the device and are the result of en gineering evaluations. typical values are for information only and are not part of the testing requirements. absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit input led continuous forward current i f 50 ma led reverse voltage i r ? 10 a v r 5.0 v output output operation: dc or peak ac load voltage i l ? 50 a v l 350 v continuous dc load current: one pole operating i l 90 ma continuous dc load curre nt: two poles operating i l 70 ma ssr ambient operating temperature range t amb - 40 to + 85 c storage temperature range t stg - 55 to + 150 c pin soldering temperature (1) t = 10 s max. t sld 260 c input to output isolation voltage v iso 5300 v rms power dissipatio n (continuous) p diss 600 mw electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit input led forward current, switch turn-on i l = 100 ma, t = 10 ms i fon 2.5 ma led forward current, switch turn-off v l = 300 v i foff 0.001 1.1 ma led forward voltage i f = 5.0 ma v f 0.9 1.2 1.4 v output on-resistance i f = 5.0 ma, i l = 90 ma r on 25 28 50 ? current limit i f = 5.0 ma, t = 5.0 ms, v l = 13 v i lmt 150 200 270 ma off-state leakage current i f = 0 ma, v l = 350 v i o 1.0 na switching characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit turn-on time i f = 5.0 ma, i l = 50 ma t on 3.0 ms turn-off time i f = 5.0 ma, i l = 50 ma t off 3.0 ms
LH1533AACTR www.vishay.com vishay semiconductors rev. 1.8, 03-aug-11 3 document number: 83831 for technical questions, contact: optocoupleranswers@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 typical characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - recommended operating conditions fig. 2 - led voltage vs. temperature fig. 3 - on-resistance vs. temperature fig. 4 - current limit vs. temperature fig. 5 - leakage current vs. applied voltage ilh1533ab_00 80 60 40 20 - 40 - 20 0 20 40 60 80 ambient temperature (c) 0 100 load current (ma) i fon = 1.5 ma i fon = 3.75 ma i fon = 4.5 to 20 ma ilh1533ab_01 t a - ambient temperature (c) led forward voltage (v) - 40 - 20 0 20 40 60 80 1.6 1.5 1.4 1.3 1.2 1.1 1.0 i f = 2 ma i f = 5 ma i f = 10 ma i f = 50 ma i f = 20 ma i f = 1 ma ilh1533ab_03 change in on-resistance (%) normalized to 25 c 60 50 40 30 20 10 0 - 10 - 20 - 30 - 40 - 40 - 20 0 20 40 60 80 t a - ambient temperature (c) i l = 5 ma ilh1533ab_04 - 40 40 10 30 20 0 - 20 - 10 - 40 - 30 - 20 0 20 40 60 t a - ambient temperature (c) 80 i f = 5 ma t = 5 ms change in current limit (%) normalized to 25 c ilh1533ab_05 90 0 50 100 150 200 250 300 load voltage (v) 70 80 60 40 30 50 20 10 0 350 400 i f = 0 ma off-state leakage current (pa) 100
LH1533AACTR www.vishay.com vishay semiconductors rev. 1.8, 03-aug-11 4 document number: 83831 for technical questions, contact: optocoupleranswers@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters package marking (example) note ? tape and reel suffix (tr) is not part of the package marking. i178009 pin one id 9.91 9.63 1.14 0.78 1.02 0.51 4 typ. 0.25 0.10 3.81 3.30 2.54 typ. 1.27 typ. 7.80 7.52 8 typ. 10.03 9.52 0.79 typ. 6.81 6.48 radius 0.3 typ. 10 3 to 7 smd iso method a 2.54 r 0.25 1.78 0.76 1.52 8 min. 11.05 lh1533 v yww h 68
document number: 91 000 www.vishay.com revision: 11-mar-11 1 disclaimer legal disclaimer notice vishay all product, product specifications and data ar e subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicab le law, vishay disc laims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, incl uding without limitation specia l, consequential or incidental dama ges, and (iii) any and all impl ied warranties, including warran ties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of pro ducts for certain types of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in gene ric applications. such statements are not binding statements about the suitability of products for a partic ular application. it is the customers responsibility to validate that a particu lar product with the properties described in th e product specification is su itable for use in a particul ar application. parameters provided in datasheets an d/or specifications may vary in different applications and perfo rmance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product co uld result in person al injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding the design or manufact ure of the part. please contact authorized vishay personnel t o obtain written terms and conditions regarding products designed fo r such applications. no license, express or implied, by estoppel or otherwise, to any intelle ctual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.
|
